EQUIPMENT AND MATERIALS

1.      5 or 10 GALLON GLASS OR CERAMIC CONTAINER OR POT

2.      1 NICKEL ROD ½ INCH DIAMETER APPROXIMATE LENGTH 12 INCHES

3.      1 COPPER ROD ½ INCH DIAMETER APPROXIMATE LENGTH 12 INCHES

4.      PLEXIGLASS SUPPORT PLATFORM OR COVER , 0.20 “ THICKNESS RECOMMENDED THIS PROVIDES A STRUCTURE FOR SUPPORTING RODS AND FLASK

a.  THIS PLEXIGLASS IS USED TO COVER CONTAINER & HOLD RODS IN PLACE

b.  SUPPORT COPPER AND NICKLE RODS BY DRILLING ½ “ HOLE ON EITHER SIDE OF WHERE FLASK WILL BE HELD IN PLACE.

c.  PROVIDE OPENING TO PLACE FLASK CONTAINING IODINE INTO  ELECTRICAL FLOW BETWEEN RODS, DOWN INTO ELECTROLYTIC SOLUTION

d.  A  SUPPORT DEVICE (CLAMP ON HEAVY DEVICE) TO HOLD A FLASK WITH A GLASS STOPPER, BETWEEN THE RODS, WITH THE IODINE SOLUTION DOWN BENEATH THE SURFACE OF THE ELECTROLYTIC LIQUID.

5.      A LONG NECK GLASS FLASK, WITH GLASS STOPPER FOR HOLDING TINCTURE OF IODINE SOLUTION, STOPPER ATTACHED WITH WIRE, ALLOWS HEATED GAS IN BOTTLE TO ESCAPE BUT KEEPS STOPPER FROM BEING SHOT OFF FLASK.

6.      BATTERY SOLUTION FOR FIVE GALLON CONTAINER (DOUBLE FOR 10)

a.  THREE (3) GALLONS DISTILLED WATER

b.  TWO (2) POUNDS COPPER SULFATE

c.  ONE AND ONE HALF (1 & 1/2) OUNCE SULFURIC ACID CP

d. ONE (1) OUNCE GRANULATED ZINC

e.  ADDED IN THIS ORDER AND ALLOWED TO SIT 24 HOURS IF POSSIBLE          

7.      AMP METER FOR MONITORING 110 VOLTS AT 30 AMPS OF RESISTANCE FOR 15 MINUTES.  CONTROL AMPERAGE BY EXTENDING RODS DEEPER INTO LIQUID

8.      VOLUME OF TINCTURE OF IODINE TO BE ELEVATED TO NASCENT STATE SHOULD NOT EXCEED 1 OUNCE OF TINCTURE OF IODINE FOR ONE GALLON OF ELECTROLYTIC SOLUTION IN CONTAINER OR POT, 3 OUNCES IN 5 GALLON POT WITH 3 GALLONS OF DISTILLED WATER

9.      TINCTURE OF IODINE SHOULD BE 1 % IODINE BY WEIGHT 99 % ALCOHOL (4.5 GRAMS OF CRYSTAL IODINE [1/100 OF A POUND]FOR 1 POUND OF EYTHL ALCOHOL)

10.    TEMPERATURE OF LIQUID SHOULD NOT BE ALLOWED TO BECOME TO HOT

11.    HOOKING THREE 10 GALLON CONTAINERS IN SERIES HELPS KEEP TEMPERATURE DOWN, THE MORE LIQUID THE LONGER TO HEAT.

12.    ELECTROLYTIC BATH SHOULD BE REPLACED WHEN IT NO LONGER HAS A CHARGE.  WITH A/C CONNECTION REMOVED A CHARGE BETWEEN RODS SHOULD SHOW ON VOLT METER OR REPLACE EVERY MONTH.  IF MUCH CHARGING OF NASCENT IODINE THEN MAYBE EVERY WEEK.

IODINE SHOULD BE TRANSFERRED TO A DARK COLORED CONTAINER FOR STORAGE AND KEPT FROM HEAT.

WHEN NASCENT IODINE IS DILUTED IT STARTS TO REACT IN NASCENT STATE.  NASCENT IODINE PREPARED THIS WAY APPEARS TO BE ACTIVE IN THE BODY FOR TWO TO THREE HOURS.  HEALTH CARE PROVIDER SHOULD BE CONSULTED ABOUT USE. SMALL DOSES MORE OFTEN ARE BETTER THAN A SINGLE LARGE DOSE.  A CYCLIC USE WITH DAYS OF REST FROM USE IS RECOMMENDED.

SETTING UP A 110 VOLT A/C CURRENT WITH 30 AMP BREAKERS ELECTRICAL CONNECTIONS REQUIRES A PROFESSIONAL ELECTRICIAN AND IS DANGEROUS TO WORK WITH. 

CARE SHOULD BE TAKEN IN SETTING THIS UP.